Sodium-ion is not a new concept — it was studied alongside lithium back in the 1980s. It stayed uncommercialised not because the principle fails, but because these three things were never engineered. King-Sodium's work is about turning them into mass-producible process windows.
The cathode sets the voltage plateau and structural stability; the anode sets sodium storage and first-cycle efficiency. King-Sodium develops both ends independently.
Polyanion cathodes use a three-dimensional framework similar to NASICON. Phosphate groups (PO₄³⁻) anchor oxygen atoms through strong covalent bonds, keeping the lattice stable as sodium repeatedly inserts and extracts — the fundamental reason for their better cycle life and thermal stability than layered oxides.
We deliberately passed on the higher-energy-density layered oxide route and chose polyanion, for a simple reason: King-Sodium's target segments are storage, backup and extreme-cold traction — where “6,000 cycles” and “no fire on nail penetration” are worth far more than “40Wh more per kilogram”.
Hard carbon stores sodium in three stages — adsorption, intercalation and pore filling — with the sloping and plateau regions together providing reversible capacity. King-Sodium controls pore distribution through biomass precursor selection and carbonisation temperature.
The cylindrical format's cost advantage comes from amortised structural parts, but a larger diameter also brings engineering challenges in winding tension, heat path and electrode alignment.
Conventional cylindrical cells draw current through a single tab: a long path with high resistance and concentrated heating at high rates. A full-tab design uses the entire electrode edge as the current path, shortening the electron path by about 40% and spreading heat across the full case length.
Cylindrical cells touch along a line, which limits the heat conduction path, so propagation between neighbours is slower than with the face contact of prismatic cells. Combined with module-level insulation pads, this effectively blocks runaway spread inside a module.
The 120420 uses one common form factor and adjusts capacity tiers via electrode formulation and stacking density, so module hardware needs no new tooling.
Uneven winding tension at larger diameters warps the electrode and causes local sodium plating. King-Sodium uses segmented tension control, holding consistency within ±2%.
Axial and radial dual-channel heat dissipation; the cold plate follows the full case length, holding module temperature spread within 3°C.
Safety cannot rely on BMS software protection, nor on users operating correctly. It must come from the physical boundary of the materials and structure themselves.
| Test item | Test conditions | Test results | Status |
|---|---|---|---|
| Overcharge | Continuous charge at 1.5× cut-off voltage | No fire, no explosion, CID trips to cut power | ok |
| Over-discharge | Discharge to 0V and hold | Recovers to normal charging, ≥95% capacity retention | ok |
| External short circuit | Direct anode-cathode short | No fire, no explosion, no case deformation | ok |
| Crush | Crushed to 30% deformation | No fire, no explosion | ok |
| Nail penetration | φ5mm steel nail through-penetration | No fire, no explosion, thermal runaway onset ≥325°C | ok |
| Thermal box | 130°C for 30 minutes | No fire, no explosion | ok |
| Thermal shock | −40°C ↔ +85°C, 10 cycles | No leakage, no swelling, ≥95% capacity retention | ok |
| Low pressure | 11.6 kPa for 6 hours | No leakage, no deformation | ok |
| Vibration | 10–55 Hz sweep for 3 hours | No leakage, no power loss, ≥98% capacity retention | ok |
| Impact | 150 g / 6 ms half-sine | No leakage, no fire | ok |
| Drop | 1.5 m concrete floor | No leakage, no fire | ok |
| Forced discharge | External reverse forced discharge | No fire, no explosion | ok |
Thermal runaway onset (nail penetration):
The higher the temperature, the longer the response window left to the BMS and fire suppression system, and the easier system-level safety design becomes.
Polyanion cathodes decompose at higher temperature than layered oxides, and the hard carbon anode contains no lithium metal, fundamentally reducing heat and oxygen generation.
Axial venting in the cylindrical case, plus a CID cut-off device and bottom current collection, block failure propagation at the cell level.
Pack-level aerosol, cabin-level perfluorohexanone, smoke detection interlock and active liquid cooling close the loop at system level.
A sodium line does not need lithium-grade ultra-low humidity, so equipment investment and running energy both fall. Those savings show up directly in cost per Wh.
Source: Luoding plant capacity validation report, March 2026.
Cost basis: cell material cost (BOM), excluding manufacturing and period expenses.
The Luoding plant is planned at 10GWh with RMB 2 billion total investment on 290 mu. Phase I is at full capacity, covering King-Sodium Series 5 consumer cylinders and 120420-280 / 600 storage cells. Phase II targets large cylindrical cells above 1,200Ah and sodium solid-liquid hybrid systems.
Patents are not certificates on a wall. Their value is locking the process window into a reproducible parameter range, so quality no longer depends on an individual engineer's experience.
Polyanion cathode doping, hard carbon precursor treatment, wide-temperature electrolyte additives and more.
Full-tab current collecting, bottom current path, large-cylindrical winding tension control and sealing structure.
Electrode coating uniformity control, staged formation current strategy, dry-room parameter window.
Module thermal management structure, pack-level fire suppression logic, EMS dispatch strategy algorithms.
| Technology pillars | Patents | Type | Status |
|---|---|---|---|
| Materials & formulation | 11 | Mainly invention patents | 6 granted / 5 pending |
| Structural design | 8 | Utility model + invention | 5 granted / 3 pending |
| Manufacturing process | 5 | Invention patents | 2 granted / 3 pending |
| System integration | 3 | Utility model + software copyright | 2 granted / 1 pending |
| Total | 27 | — | 15 granted / 12 pending |
The parameter ranges below are core King-Sodium technical assets, protected by both patents and trade secrets; the technical pack provides application-level parameters only.
King-Sodium's white paper “Engineering path of polyanion sodium-ion batteries” and full test reports are available on request. Tell us your technical focus in the enquiry and we'll arrange the right engineer.